Change the initcall level of qpnp-misc driver from module_init()
to subsys_initcall() so that the misc devices can be available
earlier. This helps the clients to access the registers under
misc peripheral sooner without a probe deferral.
Change-Id: Ie5df2cb9cf6842c59ec6f00ac9123994111f207b
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
While in DRP the legacy cable detection may fail. When a legacy cable is
detected the legacy input current limits are enforced by hardware.
Always assume a legacy cable since the legacy cable detection will
fail in some cases. Manually enforce the legacy input current limits to
ensure USB stability and compliance. As a side effect, non-legacy 22k
ohm and 10k ohm Rp adapters will be current limited to legacy standards.
To realize this:
- Set a limit of 100mA as soon as type-c is connected and remove that
limit once PD is confirmed.
- If PD is not confirmed:
- SDP: Use 100mA vote until USB PHY updates it to 500/900mA
- CDP: Use 1.5A vote
- DCP: Use 1.5A vote
- HVDCP: Use 3A vote
Change-Id: I049a7ee2099acd9e58df1b9417847daec4854af5
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
While in DRP the legacy cable detection may fail. Legacy cable
detection is essential to preventing CC OV damage.
Always assume a legacy cable since the legacy cable detection will fail
in some cases. As a side effect, non-legacy HVDCP adapters will stay at
5V if they have a 10k ohm Rp.
To realize this:
- Remove disallowing PD based on the legacy bit being set. That bit set
or unset is not reliable and it is safe to try PD.
- Remove the workaround which tries to fix legacy cable being set
incorrectly at boot. That bit set or unset is not reliable.
Change-Id: I37879866592f63906a7c688f51c309b4e2fee48d
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Currently to override the ICL the self-clearing ICL override bit is
used. The problem with this bit is that it is self-clearing and a
separate register needs to be read to get the override status.
Furthermore, the hardware will automatically clear this bit on USB
removal.
A new ICL override bit was added in PMI hardware revision 2.0. This bit
is not self-clearing, and can be set prior to USB insertion. Use this
new bit.
Change-Id: I30a601b6aacba3c404ebdfb82e529504a694a048
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Currently AICL will be rerun whenever PD requests a voltage increase.
While this works in most cases it can become problematic if PD requests
the same voltage twice, and the ICL may fall to ICL_MIN.
Since the voltage requests originate in the userspace it would be less
error prone to allow the userspace to rerun AICL instead. Do it.
Change-Id: Id190564e28bcffd72a1de70fa1327fce3e40299e
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
When APSD_START_ON_CC_BIT is set both VBUS and CC must be attached
before APSD runs. This eliminates all issues related to slow plugin.
Unfortunately this means that if CC is re-asserted anytime after APSD
finishes, then it will rerun again.
Fix this by disabling APSD_START_ON_CC_BIT right after CC is asserted,
and enable it after USB removal.
Change-Id: I27d3727647635b78392b925f0881dc3a4ef41623
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
A client vote can be enabled or disabled. Add an API which allows
consumers to check the enable/disable status of a client vote.
Change-Id: Ic4e9224c19e63fb88216da0cb775994e3e87c1f7
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Increase the strength of camera mclk0 on msm8998 HDK.
Change-Id: I9804d26265f074e1696f9b324ac8973100bb0a0e
Signed-off-by: Wei Ding <weiding@codeaurora.org>
Improve touch device setting is needed by QTC800H only. So move
the node to qrd dts from common file.
Change-Id: I1c04e2b2540a4db9dff839ebe3dfe45efe552c9a
Signed-off-by: zhaoyuan <yzhao@codeaurora.org>
HDK835 has HDMI and DP hardware blocks, so enable them in the
device tree.
CRs-Fixed: 2012660
Change-Id: I04a58527875bd6c62d7d31e20bc4ade3824d7e03
Signed-off-by: Ray Zhang <rayz@codeaurora.org>
