On sdm630, amoled panel needs VDDIO needs 1.8V on ldo11 and not
1.88V. Update the vote on ldo11 from 1.88V to 1.8V.
Change-Id: Ic6e6eae1a7c616236b2ba39b42c5f5b797b4d42c
Signed-off-by: Ashish Garg <ashigarg@codeaurora.org>
rm67195 fhd command panel will be used for SDM630
PM660A QRD, add panel supply entries for this AMOLED
panel, add brightness DCS control type for this panel,
enable this display panel for SDM630 PM660A QRD.
Change-Id: I6c3e137f55ab9662cab3d238c2e2f5e72fa73ca6
Signed-off-by: Yahui Wang <yahuiw@codeaurora.org>
mhi clients can manage both hardware and software event rings.
Process incoming data based on event ring type instead of
channel type.
CRs-Fixed: 2018326
Change-Id: Ifa2de76034224c19a846f7be153400888f8c66de
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
When a client ask MHI host to processed X number of events, only count
transfer events as part of processed events. All other events are internal
events.
CRs-Fixed: 2018324
Change-Id: I4cfcae0ba187348442c3fc45b76d7c4b01f687bd
Signed-off-by: Sujeev Dias <sdias@codeaurora.org>
Change the initcall level of qpnp-misc driver from module_init()
to subsys_initcall() so that the misc devices can be available
earlier. This helps the clients to access the registers under
misc peripheral sooner without a probe deferral.
Change-Id: Ie5df2cb9cf6842c59ec6f00ac9123994111f207b
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
While in DRP the legacy cable detection may fail. When a legacy cable is
detected the legacy input current limits are enforced by hardware.
Always assume a legacy cable since the legacy cable detection will
fail in some cases. Manually enforce the legacy input current limits to
ensure USB stability and compliance. As a side effect, non-legacy 22k
ohm and 10k ohm Rp adapters will be current limited to legacy standards.
To realize this:
- Set a limit of 100mA as soon as type-c is connected and remove that
limit once PD is confirmed.
- If PD is not confirmed:
- SDP: Use 100mA vote until USB PHY updates it to 500/900mA
- CDP: Use 1.5A vote
- DCP: Use 1.5A vote
- HVDCP: Use 3A vote
Change-Id: I049a7ee2099acd9e58df1b9417847daec4854af5
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
While in DRP the legacy cable detection may fail. Legacy cable
detection is essential to preventing CC OV damage.
Always assume a legacy cable since the legacy cable detection will fail
in some cases. As a side effect, non-legacy HVDCP adapters will stay at
5V if they have a 10k ohm Rp.
To realize this:
- Remove disallowing PD based on the legacy bit being set. That bit set
or unset is not reliable and it is safe to try PD.
- Remove the workaround which tries to fix legacy cable being set
incorrectly at boot. That bit set or unset is not reliable.
Change-Id: I37879866592f63906a7c688f51c309b4e2fee48d
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Currently to override the ICL the self-clearing ICL override bit is
used. The problem with this bit is that it is self-clearing and a
separate register needs to be read to get the override status.
Furthermore, the hardware will automatically clear this bit on USB
removal.
A new ICL override bit was added in PMI hardware revision 2.0. This bit
is not self-clearing, and can be set prior to USB insertion. Use this
new bit.
Change-Id: I30a601b6aacba3c404ebdfb82e529504a694a048
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Currently AICL will be rerun whenever PD requests a voltage increase.
While this works in most cases it can become problematic if PD requests
the same voltage twice, and the ICL may fall to ICL_MIN.
Since the voltage requests originate in the userspace it would be less
error prone to allow the userspace to rerun AICL instead. Do it.
Change-Id: Id190564e28bcffd72a1de70fa1327fce3e40299e
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
When APSD_START_ON_CC_BIT is set both VBUS and CC must be attached
before APSD runs. This eliminates all issues related to slow plugin.
Unfortunately this means that if CC is re-asserted anytime after APSD
finishes, then it will rerun again.
Fix this by disabling APSD_START_ON_CC_BIT right after CC is asserted,
and enable it after USB removal.
Change-Id: I27d3727647635b78392b925f0881dc3a4ef41623
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
A client vote can be enabled or disabled. Add an API which allows
consumers to check the enable/disable status of a client vote.
Change-Id: Ic4e9224c19e63fb88216da0cb775994e3e87c1f7
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
ESD feature is enabled on the nt35597 truly panel on sdm660 to
check the panel status periodically.
Change-Id: Id354c900a784b1bf239595fd31a244c064066987
Signed-off-by: Ashish Garg <ashigarg@codeaurora.org>
For some panels, escape clock needs to be updated for checking
the panel status periodically. Update the panel init sequence
to increase the escape clock.
Change-Id: I4a154d30e829c80587b3207ddc754aace927ab1c
Signed-off-by: Ashish Garg <ashigarg@codeaurora.org>
Increase the strength of camera mclk0 on msm8998 HDK.
Change-Id: I9804d26265f074e1696f9b324ac8973100bb0a0e
Signed-off-by: Wei Ding <weiding@codeaurora.org>
Do asynchronous driver probing of TZ log driver to improve
the device boot-up time.
Change-Id: Ic972be12f820787db1a5bc957b109461354875fb
Signed-off-by: AnilKumar Chimata <anilc@codeaurora.org>
Signed-off-by: Zhen Kong <zkong@codeaurora.org>
Improve touch device setting is needed by QTC800H only. So move
the node to qrd dts from common file.
Change-Id: I1c04e2b2540a4db9dff839ebe3dfe45efe552c9a
Signed-off-by: zhaoyuan <yzhao@codeaurora.org>
HDK835 has HDMI and DP hardware blocks, so enable them in the
device tree.
CRs-Fixed: 2012660
Change-Id: I04a58527875bd6c62d7d31e20bc4ade3824d7e03
Signed-off-by: Ray Zhang <rayz@codeaurora.org>
