Change FnR rule creation prints to low in order to avoid IPC
logging flood.
Change-Id: Ie1f0f48ffc1fd67fc8a2074d3d334fb8cd29c99f
CRs-Fixed: 1064336
Acked-by: Ady Abraham <adya@qti.qualcomm.com>
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
Clock must be set before enabling it.
Enabling clock before setting it may run the clock at a lower
rate than required.
CRs-Fixed: 1046014
Signed-off-by: Rajesh Bondugula <rajeshb@codeaurora.org>
Change-Id: I92618b736e637b1575a77a7fc18dd384919ed927
Regulator enable and disable of CSIPHY depends on the CSID module.
Make the enable and disable of clk regulator independent of CSIPHY.
CRs-Fixed: 1050172
Change-Id: Iefd57ae1c3fb5774b8043ef2e824acbacc8d16d2
Signed-off-by: Viswanadha Raju Thotakura <viswanad@codeaurora.org>
Add top-level wcd934x codec registers as volatile because
those registers get updated even before register map cache
initialization.
Change-Id: Ibdf5f695e5464b9597d153f725ff461f89b62ae4
Signed-off-by: Phani Kumar Uppalapati <phaniu@codeaurora.org>
For MSMCOBALT QRD SKUK board, add a new file for the new wqhd command
panel. And enable it in the board.
Change-Id: Iac5b202343bcf0265baf7732196b33dc5fe9c18d
Signed-off-by: Mao Flynn <feim1@codeaurora.org>
Remove code that reads firmware from the header file,
this feature is not supported.
Change-Id: I6c18e153ddf18667ca83d47df20c71bce6dbfa21
Signed-off-by: Himanshu Aggarwal <haggarwa@codeaurora.org>
Remove irq polling from Goodix driver. Use interrupt based
mechanism to process interrupts from touch controller.
Change-Id: I0a9037eac6e30a6319919043dd2ef1c226663af9
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
Signed-off-by: Sudhakar Manapati <smanap@codeaurora.org>
In cases where we do not use the CONFIG_COMMON_CLK_MSM
and clients who use clock_debug_print_enabled would fail
compilation. Fix the same by adding the config check.
Change-Id: Iaa878754e1d769056a621066eb8a73e1bc55d3a0
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
For ADSP SVA, MAD cannot work without MCLK. Connect them so that
dapm can power MCLK up.
CRs-Fixed: 1070327
Change-Id: Ia79f862379ad32e5a44dce6bdc905d2083a45b60
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
To support ADSP SVA with wcd934x codec, audio codec path needs to
be set up from MAD module to slimbus port. Establish the path and
reserve the slimbus TX13 port for it.
CRs-Fixed: 1070327
Change-Id: I4cc20bd7070a51a121a0da33c9b30233443bb543
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
Current implementation for getting fw files for a target is
supported only in PCIE based QCA chipsets. Add support to
get FW files for QCA SDIO targets.
CRs-Fixed: 1036232
Change-Id: If6c273d9a86f9fc4bc841388b11b96c385dc64f4
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Add support for CTI, DCC and Watchdog for msmfalcon. DCC is used for
capturing register values and CTI is used to map triggers.
Watchdog is used to handle kernel panics.
Change-Id: I4202cfb21868983792e75e8ef6a305030879fb39
CRs-fixed: 1056777
Signed-off-by: Amey Telawane <ameyt@codeaurora.org>
Add threaded irq support to Goodix touchscreen driver to reduce
the time spent with interrupts diabled to a bare minimum by
pushing the processing out into the kernel thread.
Change-Id: I3ade13181957d327ad9d0266b1999a4b0f2d8d1a
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
Request TZ to unlock WLAN doorbell register for ipa
uC access for offload data path.
Change-Id: Ia79b1d8a9a0213c2f5296140bff7a36d3f035e21
Acked-by: Shihuan Liu <shihuanl@qti.qualcomm.com>
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
Driver sets the speed using extcon cable state flag. This
allows to start host or peripheral in selected speed.
By default start peripheral in super speed mode. However,
starting host in super speed consumes more power so to
achieve lower consumption default it to high speed only.
Add module params to override the default behavior as follows:
# echo Y|N > /sys/module/policy_engine/parameters/ss_dev
# echo Y|N > /sys/module/policy_engine/parameters/ss_host
Change-Id: I2a45a4149f593a129b4dd123df730405169404f9
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Some SMMUs can walk page tables in the CPU cache. Enable this
behavior for SMMUs whose device tree node has the `coherent'
property set.
Change-Id: Icbb7a7eaf6c6e85c3ff4f981fe1dd1c3917228dc
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
Coherent devices can make use of the CPU cache, so they should get
coherent IOMMU mappings and should have their cache maintenance
operations skipped. Implement this for the vanilla arm64 IOMMU mapper.
Change-Id: Iab6715a071a5fa5556934d7771a6d07d678e9703
Signed-off-by: Mitchel Humpherys <mitchelh@codeaurora.org>
On vfe48 the write masters need to be reenabled after vfe h/w reset.
CRs-Fixed: 1067996
Change-Id: I3ca87ec06e6204e3cecb137d8d8b4f1cedfc3fe1
Signed-off-by: Shubhraprakash Das <sadas@codeaurora.org>
When stream is stopped the undelivered buffers are flushed but
the count is not set back to 0, fix this.
CRs-Fixed: 1067674
Change-Id: I2e31912667be7bb9d0179b655b8bed425d18a869
Signed-off-by: Shubhraprakash Das <sadas@codeaurora.org>
Before operating on the streams sent by userspace ensure that
the stream handles sent from userspace are correct.
CRs-Fixed: 1064457
Change-Id: I0bde105ac751f9e26572efc387dfd88414e0c22d
Signed-off-by: Shubhraprakash Das <sadas@codeaurora.org>
When setting the stream satte to UPDATING the active completion
should be initialized since we wait on that completion.
CRs-Fixed: 1064457
Change-Id: Ia17d8fb224ef2709761f03464aaf2d4541566817
Signed-off-by: Shubhraprakash Das <sadas@codeaurora.org>
Use mmssnoc_axi clk instead of maxi_clk. Only, mmssnoc_axi
clock is needed to satisfy the camera clock dependencies.
CRs-Fixed: 1066418
Change-Id: I92b8ff43f3b4604bba43aa1eb1ea110863bd12a7
Signed-off-by: Shubhraprakash Das <sadas@codeaurora.org>
Change FnR rule creation prints to low in order to avoid IPC logging
flood.
Change-Id: I18a27267eebdca2c87bf4bffc11a120822cdc7c2
CRs-Fixed: 1064336
Acked-by: Ady Abraham <adya@qti.qualcomm.com>
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
To prevent sleep current leakage, leave L7A/L17A/L25A
turn on during sleep and set LPM/NPM by pin control.
Change-Id: I787d3b4300fae8fb04ac1aa8d3b27b71e8bd7797
Signed-off-by: Sungjun Park <sjpark@codeaurora.org>
Increase the timeout in SSR case for TAG completion
as IPA might be slow in processing this command.
Change-Id: I5cfadb3ee7cb339b89b0c428bae46d3802476eb9
CRs-Fixed: 1064336
Acked-by: Ady Abraham <adya@qti.qualcomm.com>
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
Avoid pop during dsd audio path tear down by enabling
mute before the slim ports are disconnected.
Change-Id: I542fab59eadbea404c0001d25315172cc993488b
Signed-off-by: Phani Kumar Uppalapati <phaniu@codeaurora.org>
Enable msmcobalt to use the audio notifier framework.
Audio notifier framework connects to the best available
framework for remote subsystem notifications such as
subsystem up or down.
Change-Id: Ib88a71e2fdb2b58fd5f87a65cb7d3253884f2d97
CRs-Fixed: 1054000
Signed-off-by: Ben Romberger <bromberg@codeaurora.org>
Modify APR driver to use audio notifier framework.
Audio notifier framework connects to best available
subsystem for remote notifications.
Change-Id: I783b7df9c7e0253e5dc88bd60e0b5300e26fba56
CRs-Fixed: 1054000
Signed-off-by: Ben Romberger <bromberg@codeaurora.org>
Enable the audio Notifier, PDR, and SSR drivers
for msmcobalt in the Kconfig.
Change-Id: Ief6e89b003aa1e2b02f33e21e3cb17f8731425ad
CRs-Fixed: 1054000
Signed-off-by: Ben Romberger <bromberg@codeaurora.org>
The audio PDR driver is used to control the process
domain restart recovery mechanism. The audio SSR
driver is used to control the Subsystem Restart
recovery mechanism. Both are controlled through the
Audio Notifier driver which determines whether PDR
or SSR is used and provides the core interface to
all audio drivers.
Change-Id: I15325c1385eaa0f0cca2c07130f2b4a997d98e1f
CRs-Fixed: 1054000
Signed-off-by: Ben Romberger <bromberg@codeaurora.org>
Add separate Kconfigs for the audio SSR, audio PDR,
and audio notifier drivers. Allows precise control
of different audio recovery mechanisms.
Change-Id: I2ab027d4a6e2cb98df5358e24f6bebacd9aecca7
CRs-Fixed: 1054000
Signed-off-by: Ben Romberger <bromberg@codeaurora.org>
Update the VDD_APC0 and VDD_APC1 CPR voltage configurations for
MSMCOBALT v2 devices in order to match the most recent guidelines
from hardware characterization. Increase the VDD_APC0 and
VDD_APC1 Fmax and intermediate Nominal corner ceiling voltages
to 900 mV. Also increase the VDD_APC0 Turbo_L1 open-loop and
closed-loop voltage adjustment to 30 mV.
Change-Id: Id2de8e2ac94476c1a4927f719f2987a31d692ab5
CRs-Fixed: 1070187
Signed-off-by: David Collins <collinsd@codeaurora.org>
Correct the minimum and maximum PM8005 SMPS 1 regulator voltage
constraints for MSMCOBALT v1 and v2 so that they encompass all
values that the VDD_GFX CPR control may need to request.
Change-Id: I479e23db73a64e0fc1371e6b5abfaf1c8969954b
CRs-Fixed: 1068464
Signed-off-by: David Collins <collinsd@codeaurora.org>
Use proper mmss clock for csiphy and set the phytimer clock rate at
200MHz.Update csiphy node with regulators needed by csiphy clocks.
CRs-Fixed: 1068060
Change-Id: Iaf8240c2a6ef0b7739f80b6d0bb30946f61a9ed0
Signed-off-by: Viswanadha Raju Thotakura <viswanad@codeaurora.org>
Add "qcom,msm-bus,name" property which is required for bus scaling to
venus pil node for MSMCOBALT.
CRs-Fixed: 1071217
Change-Id: I37e6f76b60ef0085d102c5d98179b467f6b77dee
Signed-off-by: Puja Gupta <pujag@codeaurora.org>
Allow callers of devm_usbpd_get_by_phandle() to distinguish
between different errors depending on what failure is encountered.
For instance, return -EPROBE_DEFER if the device is available
but not yet probed, which allows callers to appropriately try
again later.
Change-Id: I96b03d0a4c2a04a405af5a40f9f713443bc5769b
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Add a new linux header to support 64 bit pagetable address in Linux OS
section.
Add a new linux context header to support v2+ Linux version in Linux
context section.
Remove multiple register reads on CP IB registers and have a single
CP register read to get the active IB information.
Add Active IBs to obj_list in case static snapshot blob is not having
enough memory, so that it get dumped into dynamic blob.
Add a message in case any active IB is not getting dumped into snapshot
binary.
Change-Id: Icee01f6ba95e469acac9eed6bf2fdbc83947f5a8
Signed-off-by: Hareesh Gundu <hareeshg@codeaurora.org>
Make clocks needed for secure touch as optional. Hence, even if the
clocks are not defined, just proceed further and initialise the secure
touch session.
Change-Id: Id8fb80ca0297bc1d1854fdc710abce6a4d2f9620
Signed-off-by: Abinaya P <abinayap@codeaurora.org>
Add debugfs entry for suspend/resume that allow suspending/
resuming of Goodix CTP driver from userspace. Also change
the return type of goodix_ts_resume and goodix_ts_suspend
functions and set the status of gtp_is_suspended in the last
of above functions.
Change-Id: Ic2b1b2562b63ccecdf15bdc64ad7e45996d196d3
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
This patch removes the possibilty of header length and read length
having negative values and thereby possible buffer corruption.
CRs-Fixed: 1002389
Change-Id: Id74650d5c4aaf9f84a56372f60ff5a40374e8f7b
Signed-off-by: Manoj Prabhu B <bmanoj@codeaurora.org>
This change removes source files from the kernel tree that
were not being used during make.
Change-Id: I5132854367330a9b47f678409cbe6a45f2b5abb3
Signed-off-by: Sudhakar Manapati <smanap@codeaurora.org>
Fix errors and warnings found by checkpatch script in
goodix_tool.c and gt9xx_update.c. Correct debug messages
in goodix_update.c. Remove magic numbers for read-write
flags with macros in goodix_tool.c
Change-Id: I3a00fb46106f859128f0fa9b8c99b5d6ba24bc7b
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
The params array is used without initialization, which may cause
security issues. Initialize it as all zero after the definition.
CRs-Fixed: 1062271
Change-Id: If462fe3d82f139d72547f82dc7eb564f83cb35bf
Signed-off-by: Walter Yang <yandongy@codeaurora.org>
ADSP requires ANC configuration to run the ANC algorithm.
Send the common configuration for both WCD9335 and WCD9340
codecs.
Change-Id: I12154b0aa315fde6dd92267d4c8f4a78a6f0236f
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
core control enables you to save power by controlling how many
cores are being used depending on the load in the system.
Change-Id: I5975f1e5d7a1947dc5ee1cf8a0c16ec88b0fc6fb
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Replace hotplug functionality in core control with cpu isolation
and integrate into scheduler.
Change-Id: I4f1514ba5bac2e259a1105fcafb31d6a92ddd249
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Refactor cpu data into cpu data and cluster data to improve readability and
ease of understanding the code.
Change-Id: I96505aeb9d07a6fa3a2c28648ffa299e0cfa2e41
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
Move the core control trace events to scheduler trace event file.
Change-Id: I65943d8e4a9eac1f9f5a40ad5aaf166679215f48
Signed-off-by: Olav Haugan <ohaugan@codeaurora.org>
