Change the power supply for msmcobalt QRD interposer platform
to use regulators from pmfalcon.
CRs-Fixed: 1090535
Change-Id: Ib1fdb0454c6e1d770ea6ec11a6032f8553d56c06
Signed-off-by: xiaonian <xiaonian@codeaurora.org>
Specify the regulators for mdss on falcon track3.
Change-Id: Ie828c8568ef09c89cff157d16d3cb322647b6f6e
Signed-off-by: Ashish Garg <ashigarg@codeaurora.org>
Add the LDO and NCP display +ve and -ve bias for LCD
display.
Change-Id: Ia85688854f26fe871d5c1253c2d51d75d84deb8f
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Add common dtsi file for msmfalcon and msmtriton. Also Add
device tree entry for super speed USB3 controller, super speed
phy and high speed phy.
Change-Id: I326eceeddff8e77d346c3365fa46cd539324451f
Signed-off-by: Chandana Kishori Chiluveru <cchiluve@codeaurora.org>
To optimize charging during power negotiation and the voltage
is not changing, for example when transitioning from implicit
contract to the default 5V PDO, there is no requirement to
suspend the charging and hence setting the charger's
PROP_PD_CURRENT_MAX can be avoided. It is only needed when
changing voltages, in which case current limit should be
calculated based on pSnkStdby (2.5W), or when staying at the
same voltage and decreasing current.
Also fix the incorrect setting of PROP_CURRENT_MAX to
PROP_PD_CURRENT_MAX when doing a sink->source swap.
Change-Id: Ib53902459646e590df4dc7fcb00f833d5e8f41ed
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Increase the refresh rate for the RRADC to support
reading refreshed USBIN voltage at a higher frequency.
To support the higher frequency at which the data
is refreshed enable continuous mode and force update
on reading every cycle on the USBIN_V trigger.
After reading the USBIN_V result set the RRADC to non
continuous mode with default trigger setting.
Change-Id: I7e9ada5de1f619c6a34a4b2e1764f5e908564ce5
Signed-off-by: Siddartha Mohanadoss <smohanad@codeaurora.org>
Clear mpm_wcssaon_config bits before top level reset.
If those bits are non-zero during WLAN is enabled,
there could be random failures.
CRs-Fixed: 1086372
Change-Id: Ia03380dfa4852c80fedb38f3c79f55d8d1a9a7f6
Signed-off-by: Yuanyuan Liu <yuanliu@codeaurora.org>
Currently we disable try.SINK right before pd becomes active and
re-enable it right after inactive. This breaks typec compliance.
To fix it, disable try.SINK mode in the probe and never enable it.
Change-Id: I61523188f45daca026b90943c845b43a8327f51e
Signed-off-by: Harry Yang <harryy@codeaurora.org>
Currently there is an issue introduced by forcing the results of
the icl_votable while pd is active. icl_votable is a min voter
and since the DEFAULT_VOTER votes 1.5Amps that becomes the max
one could draw when pd is active. This is incorrect and hence the
issue.
Note that DEFAULT_VOTER is only needed while DCP is present.
So, to fix it, rename DEFAULT_VOTER to DCP_VOTER and make DCP_VOTER
unvote and vote when pd_active is set and unset respectively.
CRs-Fixed: 1091477
Change-Id: I7435f05f20e12a7704ae5d9597b5cdc9b5a61d00
Signed-off-by: Harry Yang <harryy@codeaurora.org>
Incorporate the 2016-10-31 updates to the internal regulatory
database. Update countries Bahrain, Belize, Chile, Egypt, Honduras,
India, S Korea, Nepal, Panama, Russia, Senegal, TT and UAE. Also
update St. Kitts&Navis and St. Lucia dfs region.
Change-Id: Ia151b2dd5229f07790ac961af298305b24e098fb
CRs-Fixed: 1091511
Signed-off-by: Amar Singhal <asinghal@codeaurora.org>
Device tree creation of new mediabox variant of
apqcobalt.
CRs-Fixed: 1091110
Change-Id: I4f8070e7fd0aa39664208cfab2448b5a95ab2326
Signed-off-by: Mohamed Moussa <mmouss@codeaurora.org>
Signed-off-by: David Ng <dave@codeaurora.org>
Smem uses static array to store legacy partition information.
New comm partition is used to replace existing legacy partition.
CRs-Fixed: 1074985
Change-Id: Ib2268181a617c23d62b5b6f857be5327113b2a67
Signed-off-by: Dhoat Harpal <hdhoat@codeaurora.org>
Enable auto GM for WLED module in pmicobalt to make LOOP_GM adaptively
changes with brightness change.
CRs-Fixed: 1081738
Change-Id: I10a788726358c56df9bfe11f2332e3823d7cd332
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
The WLED boost controller in pmicobalt supports auto PFM mode when
LCD mode is selected. Auto PFM mode is enabled by default except
on some specific hardware versions. Add a property to specify
AUTO_PFM_THRESHOLD for the boost controller so that it can enter
PFM mode when the adaptive headroom voltage falls below the
threshold.
CRs-Fixed: 1081738
Change-Id: I964b3452d0cdb3618b4ab446655ae75fa3a1049d
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
This reverts 'commit d3c76b29e6 ("defconfig: msm: avoid compilation
of MDSS DP driver for 32-bit msmfalcon")'. The compilation of MDSS DP
driver was disabled for 32-bit msmfalcon earlier to avoid compilation
issues. The related issues are now resolved. Hence, enable back the
compilation of DP driver.
Change-Id: I9f928f0aad6af346de43965755beb039e422047a
Signed-off-by: Padmanabhan Komanduru <pkomandu@codeaurora.org>
In external codec machine driver, register
SSR notifier after sound card register. Also,
add separate snd_soc_card variables for tavil
and tasha since same machine driver is used
for both codecs.
CRs-Fixed: 1083537
Change-Id: I73fc02b812f2e6694e2a6aa8bdad2381a5f19406
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Add required machine driver support for
USB Audio, BT, FM, TDM interfaces both
for internal and external codecs.
CRs-Fixed: 1083537
Change-Id: I3d2765535793d6ef9153cfcab4b44a9adad67e15
Signed-off-by: Laxminath Kasam <lkasam@codeaurora.org>
Set required USB core clock rate for USB3 working across connect/
disconnect for msm8996. Else USB enumeration fails after reconnection
due to this invalid clock rate setting for USB core clock. Also
set USB core clock rate for USB2 controller as well.
Change-Id: I6ce48512df5973bf8a2a3081a3a6f8759aeb499f
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Updating the debug uart BLSP1UART2 gpios as per the latest
hardware definitions.
Change-Id: I9cda84d1c199b72ce8b9e2997601bcc7430ddbf3
Signed-off-by: Venkatesh Yadav Abbarapu <vabbar@codeaurora.org>
UART and SPI gpios are changed as per latest hardware definitions,
so updating them.
Change-Id: I0e06be169edc2eb1d35ef7fc6c41ff1809aebd03
Signed-off-by: Venkatesh Yadav Abbarapu <vabbar@codeaurora.org>
Enable the support for gladiator error reporting. Also enable
the gladiator hang detect feature.
Change-Id: I7220ad565212c325514301e4c59415b807deb99a
Signed-off-by: Venkatesh Yadav Abbarapu <vabbar@codeaurora.org>
