Currently hardware based OTG soft start will fail when enabling OTG with
high capacitance.
Fix this by implementing a software based OTG soft start sequence in
addition to the underlying hardware OTG soft start.
This soft start workaround will begin when an OTG over-current interrupt
is triggered.
Change-Id: I2f3fd5f1bb6e792b2b353eb241d83548e33f563b
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The clock to the PM660 charger has to be configured in the
CHG_FREQ module instead of CHG_MISC. Also, the charger
frequencies for PM660 and PMI8998 are different, add
logic to handle that.
CRs-Fixed: 1104287
Change-Id: I5f4daf9354b209226a03b4f8026e20be8a73348b
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
commit 1eec2157d8 ("usb: dwc3: Update core clock rate based on
USB port speed.") only sets clk rate for HS/FS/LS device add notification.
In case super speed device is plugged in after LS/FS/HS device unplug in
absence of runtime suspend, core clk rate remains at high speed core clk
rate. Fix this issue by setting the core clk rate back to default when
a device is being removed from root hub.
Change-Id: I0ac37b7ff08a9a297441304eb2cfaff398d44bb9
Signed-off-by: Hemant Kumar <hemantk@codeaurora.org>
The threshold comparators should be set to "<=". Set them.
Change-Id: I45cf6dd7f165d20e2f2dbc6fce7fd321b4ac145a
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The temperature change IRQ is used to update the parallel power supply
when the temperature of the connector changes. Enable it.
Change-Id: I26582ffc2c98183c75f5c302386416e840bd6ed0
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The connector thermal regulation source must be enabled in order to
receive temperature-change interrupts. Enable it.
Change-Id: I9bb2d3eaf3bba1b1f40bfd724060f2fa437235b5
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Add a device tree property qcom,connector-temp-max-mdegc to configure
the connector temperature at which mitigation should start.
This will set the thresholds for when the temperature-change IRQ will
fire.
Change-Id: I47df477b56a6654fbf94b5bb0f7dfdfb80e2f16e
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
Use the CONNECTOR_THERM_ZONE property to show the current thermal zone
of the USB connector temperature.
Change-Id: Ia9a85055d68ed08aa9be5b2b66e3e6389ec2e6c3
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The CONNECTOR_THERM_ZONE property shows which thermal zone the
connector temperature is currently in.
Change-Id: I669344feea13f34f98ee808cae5649766543201a
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The temperature change IRQ is used to notify the CTM driver that the
connector temperature has changed. Enable it.
Change-Id: Ibda88fcac6044c0f9a1db96be70b7e7f99e6fb73
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The charger temperature threshold should be configured for thermal
balancing. Add a device tree property to configure the temperature
threshold. A default value will be used in the absence of this property.
Change-Id: I5d64a8012a9c13c578714d91f1e7e4426cef235a
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The hardware conversion triggers are required for thermal regulation.
Enable them.
Change-Id: I4172f7ae8df437ba3a49e6abae587298bc11d78b
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
The TADC hardware supports configuring temperature thresholds. Add
support for configuring these thresholds via the IIO framework.
Change-Id: Ib673965eb9b8265874580c8c26f72c85590151c2
Signed-off-by: Nicholas Troast <ntroast@codeaurora.org>
In WCN3990, currently firmware gets loaded via non bmi procedure.
Since, firmware-5.bin file is not needed, this change skip parsing
and loading of the same.
CRs-Fixed: 2002151
Change-Id: I7e02349d73d333296b7beefa4c9cfc435de8f1a4
Signed-off-by: Rajeev Kumar Sirasanagandla <rsirasan@codeaurora.org>
Base address needs to be set for SAP interface
in HL 1.0 firmware. If base mac address has not
encoded in WLAN firmware board data file then auto
generate base mac address using device serial number
and user defined mac address.
Change-Id: I66f72c3c14b620107b48664d753c9dcf7a9b418e
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
Add TLB dump entries to setup memory space by the cpuss dump
driver to dump TLB entries.
Change-Id: I4193191d85e3839d0fb7e7d38fee4e938d55167b
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Update the nt35597 truly panel init sequence to reduce the
high latency issue seen across suspend resume cycles on
SDM660 target.
Change-Id: I0d71cebd5571fac293a8b0f401d882342fbd9106
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
The gcc_rx2_qlink_clkref_clk is not required by
any client, so remove controlling the clock from
HLOS clock driver.
Change-Id: I20dbb38f3f0fcbcdb3974923f4a0b540153d3fde
Signed-off-by: Amit Nischal <anischal@codeaurora.org>
Recovery can be initiated any time and can happen during driver
register also. With current implementation, if recovery starts
just before driver register then probe call back will not be
called as FW is not ready yet but probe call back will not be
called even after FW ready indication. Fix this case by calling
probe call back after FW ready if driver is registered but probe
call back is not called during driver register.
CRs-fixed: 2002797
Change-Id: Ia1ea812a1bac3204ad95a62b7c6e55511753f2db
Signed-off-by: Prashanth Bhatta <bhattap@codeaurora.org>
Update truly FHD panel init sequence to fix corruption
issues. Also enable dfps feature for the video mode panel
on SDM660 target with the updated sequence.
Change-Id: Ife010a0fccefad802877fd50f222587be36d24aa
Signed-off-by: Sandeep Panda <spanda@codeaurora.org>
GPU subsystem in sdm630 is supplied by either LDO300(VDD_GFX)
in LDO mode or VDD_CX in BHS mode. This LDO300 is CPR managed
and supports CPR closed-loop operation. Add CPR device node
with required configuration for supporting CPR closed-loop
operation for sdm630.
CRs-Fixed: 2000929
Change-Id: I9a07d9b00ed3830e5146b7b1debe84a9393fafd3
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
Update GFX LDO CPR closed-loop target quotients as per silicon
characterization data and also update ro scaling factor values
for sdm660.
Also, change the supported Fmax from 800Mhz to 750Mhz in GFX LDO
CPR device node.
CRs-Fixed: 2001053
Change-Id: I032a4cd13490314b15b3abd289eb5ef541e18c56
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
Display port pixel clock source is required to propagate the set rate to
parent, so update the flags for the same. The lowsvs frequency has got
updated to 154MHz, update the same.
Change-Id: I67a5ff3b5fb18c2ce986c5f431f4e41a78fe13a5
Signed-off-by: Taniya Das <tdas@codeaurora.org>
The display port PLL generates only limited set of frequency combinations.
As fractional dividers are not required to be used, update the RCG ops to
take care of the same.
Change-Id: I601273fee044ef128dbc7c2e23bc2d8ce10e31dc
Signed-off-by: Taniya Das <tdas@codeaurora.org>
GPU RBCPR clocks needs to be registered separately as GFX CPR
requires the rbcpr clocks to register the regulator handle.
Change-Id: I18275df08b1ad91dde09ac4fbea709d08162eec9
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Rotator and MDP share same stream ID on sdm600 target,
hence share the smmu device with rotator device to map/unmap
its buffers.
The change will also handle different secure usecase concurrencies
like, mdp running in secure and rotator in non-secure and vice versa.
Change-Id: I3ff118baed3984d63e9a9fe94289d99523c7b3e9
Signed-off-by: Kalyan Thota <kalyant@codeaurora.org>
Keep gcc_bimc_gfx_clk always on to prevent a stall during BIMC redirection
handshake that occurs as part of a transition between different CCI power
modes.
Change-Id: Id027d4c3ba3ef15b24cfc2747b1a7b82a206fc31
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Add device tree files for headset jacktype NO, for CDP
and RCM platforms of SDM660.
Change-Id: I32bfb871ced7a682016af8bec5eeb28dc27a3616
Signed-off-by: Neeraj Upadhyay <neeraju@codeaurora.org>
Add a property to the PD PHY peripheral to specify the default
sink capabilities for USB PD as 5V @ 3A, 9V @ 3A and 12V @ 2.25A.
These are common values that should be supported on most boards,
but can be overridden as necessary.
Change-Id: I5ea95d2f0532c59f7d83cb608d939ad28a8bb28e
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Add a device tree property to allow specifying the supported
set of sink capabilities. If not specified, fall back to a
single capability of 5V @ 3A.
Change-Id: I394061d9f3070099e35b651ce4b63a7993343bf1
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Factory QNOVO IADC OFFSET trim values are wrong polarity. To fix it,
update both (reg QNOVO_IADC_OFFSET_0 and QNOVO_IADC_OFFSET_1) with
their two's compliment, respectively.
Factory setting of QNOVO_STRM_CTRL is also wrong. It controls
polarity of the raw IADC bitstream. To get the correct IADC bitstream
polarity, set 0 to register QNOVO_STRM_CTRL.
Set range [1,255] for QNOVO PPCNT parameter, so the right value can
be written.
Change-Id: I7be948b09c96aae4077a8f010c951c6ebd22a0fa
Signed-off-by: Harry Yang <harryy@codeaurora.org>
Current driver read if any nrt vbif is present
and if it is not, the number of qos priority
levels gets wiped out, causing the driver
not to program the vbif qos priority levels for
the rt client. Fix this problem by making sure
that if a vbif nrt does not exist in the platform,
driver only ignore the nrt settings, but keeps
programming the vbif rt.
Change-Id: I2fe5eea5a2ff852b22a59cdb0139b17f3dd7c494
Signed-off-by: Ingrid Gallardo <ingridg@codeaurora.org>
Fix error check of data_len for athdiag read message. Report
error when response message's data_len is smaller than what
is expected.
CRs-Fixed: 2002939
Change-Id: I87c0c6265934ac7a3aad5dfa471c23332b7f6996
Signed-off-by: Yuanyuan Liu <yuanliu@codeaurora.org>
Add support for multi-copps for multiple BEs with independent
calibration data. This allows for more accurate calibration of device
copps.
CRs-fixed: 1110411
Change-Id: I72ce501408a474eb620a088172e3c4d789ab5ef0
Signed-off-by: Siena Richard <sienar@codeaurora.org>
Enable panel orientation property in QRD device to flip
the panel by 180 degrees for msm8998 target.
Change-Id: I3e91ed69de150b970d2e1678833d0d4cca659eef
Signed-off-by: Harsh Sahu <hsahu@codeaurora.org>
Since the page offset can be greater than the size of a page fix
arm_coherent_iommu_map_page so that it maps to nearest page
boundary.
This both prevents unnecessarily mapping memory we don’t need to
map and fixes a bug where the unmap wasn’t unmapping this extra
memory.
Change-Id: Iaa69aff7505ee75d1f2e69bb0cda814bc6211bd3
Signed-off-by: Liam Mark <lmark@codeaurora.org>
Adapt to latest changes to IPA micro-controller (IPA uC).
For pipe SUSPEND, IPA uC will fail in case the pipe is not empty.
IPA driver needs to insure pipe is empty and then issue a SUSPEND command.
For pipe DISABLE, pipe is already empty on SUSPEND,
IPA driver does not need to do ensure anything before
issuing a DISABLE command.
Change-Id: Icfc4745c666997c63be6e9444bf611fb4cbd1934
CRs-Fixed: 2002190
Acked-by: Ady Abraham <adya@qti.qualcomm.com>
Signed-off-by: Skylar Chang <chiaweic@codeaurora.org>
