Trigger preemption from the interrupt handler. This allows us
to aggressively change ringbuffers especially to lower priority
ones and finish working on pending commands.
Change-Id: Ic05213f3d02b1bb7400461edd0d19e38d5b01ec2
Signed-off-by: Sharat Masetty <smasetty@codeaurora.org>
There is a bug in usb ICL (input current limit) votable callback
where it fails to set the current on main charger if the new value
is lower than the settled value.
Fix it.
Change-Id: I8e8e1c16772eabe9f411c3de5460ca581a3a5d37
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Move battery nodes under /vendor path. This will help in overlaying
this node from board overlay files.
Change-Id: Ide144e38a1ba21dea65b1ae6d91024de30f1b3c6
Signed-off-by: Shashank Mittal <mittals@codeaurora.org>
Signed-off-by: Subbaraman Narayanamurthy <subbaram@codeaurora.org>
During card initialization, for hs400 enhanced strobe
mode we already set the bus width to 8 as part of
mmc_select_hs400.
i.e: mmc_init_card->mmc_select_timing->mmc_select_hs400
Commit 5a86b1150f ("mmc: core: fix multi-bit bus width
without high-speed mode") modified bus width selection mode
for hs400(mmc_select_bus_width is being called twice now)
which is resulting in switch command failure(-110 error).
Fix this by adding condition to check if hs400 is supported
before bus-width selection.
Change-Id: I698260599276a251ffbe2f242175be0dc51a91de
Signed-off-by: Sayali Lokhande <sayalil@codeaurora.org>
Strcpy has no limit on string being copied which causes
stack corruption leading to kernel panic. Use strlcpy to
resolve the issue by providing length of string to be copied.
CRs-fixed: 1048480
Change-Id: Ib290b25f7e0ff96927b8530e5c078869441d409f
Signed-off-by: Amey Telawane <ameyt@codeaurora.org>
To realize section mapping of 2MB in arm64 iommu mappings,
set ARM64_DMA_IOMMU_ALIGNMENT to 9 so that 2MB aligned
virtual address can be allocated based on size.
2MB section mapping in iommu page tables would ensure less
pressure on TLBs.
Change-Id: Id22e935e113bee2a4ae7aeab15bcf17b7b6f3c78
Signed-off-by: Shiraz Hashim <shashim@codeaurora.org>
Add secondary QUSB2 PHY node and put it in reset state for SDM660
to avoid leakage current issue.
Change-Id: Iab057c22268408f90ac59f9dc4b0d538edd819b9
Signed-off-by: Vijayavardhan Vennapusa <vvreddy@codeaurora.org>
Charger driver probe might fail while querying for battery
health if bms psy is not available. Fix this by reporting
health as "UNKNOWN".
CRs-Fixed: 2029960
Change-Id: I6544788a6fe3ab7aaf70ffd382213d8b4aa4c0b6
Signed-off-by: Ashay Jaiswal <ashayj@codeaurora.org>
This patch adds a way to publish APPS support
of untagging header only to selected peripherals.
CRs-Fixed: 2030651
Change-Id: I2a2a03d0a6d441d23ec093ff5de9bef5e9799d24
Signed-off-by: Manoj Prabhu B <bmanoj@codeaurora.org>
Add a new value to the oob_mode module parameter for
supporting AP certification.
All enabled values of oob_mode (>0) are intended only
for debugging and diagnostics.
Change-Id: I170c953b0f126513b6fec7a7c316d282ed56367e
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Git-commit: b8c31b5d6c232a36c821bdd556b60c033a1c1577
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
[merez@codeaurora.org: fix trivial merge conflicts]
Signed-off-by: Maya Erez <merez@codeaurora.org>
Driver always invoke cfg80211_disconnected() with locally_generated as
false.
Fix this by reporting true whenever the disconnect is triggered from
upper layers (cfg80211) or from within the driver itself (reset,
deinit).
Change-Id: I367797e0eeb1e71a28674415121a054daee04cbc
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Git-commit: 3b56c15fa3315942b4cb02e57ff842f2f9b14ef7
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
Signed-off-by: Maya Erez <merez@codeaurora.org>
Upon connect timeout driver invokes _wil6210_disconnect() which iterates
over sta array and disconnects each connected sta. In practice, because
the connection is still ongoing and because cid is not yet allocated,
disconnect is not actually happening. This leaves FW in connecting
state while driver is in disconnected state.
To fix this, upon connect timeout, explicitly send WMI_DISCONNECT_CMDID
to FW to make sure it gets disconnected.
Change-Id: I4d6ed85f00901b0e286d8b05d016e9cd5e9dd2fb
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Git-commit: 628639b1c976a5f02792dc6595a4d199b7b70d85
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
Signed-off-by: Maya Erez <merez@codeaurora.org>
In a fast disconnect/connect sequence, cfg80211_connect_result() can
fail to find the bss object which the driver is connecting to. Detailed
sequence of events:
* Driver is connected in STA mode
* Disconnect request arrives from user space. Driver disconnects and
calls cfg80211_disconnected() which adds new event to the
cfg80211_wq worker thread
* Connect request arrives from user space. cfg80211_connect() stores
ssid/ssid_len and calls rdev_connect()
* __cfg80211_disconnected() runs in worker thread and zero
wdev->ssid_len
* Connect succeeds. Driver calls cfg80211_connect_result() which fails
to find the bss because wdev->ssid_len is zero
To overcome this, upon connect request, store the bss object in the
driver and upon connect completion pass it to kernel using
cfg80211_connect_bss().
Change-Id: I48b7f638e3c69bf2c223ecf65d080fb603fc26f8
Signed-off-by: Dedy Lansky <qca_dlansky@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Git-commit: bcdd49b074d0ea48f54bc6d24a66efab8688b43a
Git-repo: git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.git
Signed-off-by: Maya Erez <merez@codeaurora.org>
Smb1355 is a derivative chip of smb1381, where features like
input current control and the tadc have been removed. Smb1355
can only be used in parallel mode and that too in mid-mid
configuration.
Note that even if smb1355 doesn't have an adc, its die temperature
could be measured by an external adc. So keep the support for
charger_temp and charger_temp_max properties.
Also smb1355's aux therm input will likely be connected to the
connector thermistor. Support connector_temp_health property.
Change-Id: I738d60ea3385c296187a9cc8afe8134feb8c615f
Signed-off-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
When PCIe host driver receives an unexpected interrupt for
global IRQ, log it to PCIe dump ipc logging to avoid
flooding kernel log.
Change-Id: Ia38e6a3597b0f86b8574f8edf5b2e0e124b02f4d
Signed-off-by: Tony Truong <truong@codeaurora.org>
