commit ac237c28d5ac1b241d58b1b7b4b9fa10efb22fb5 upstream.
The Creative Audigy SE (SB0570) card currently exhibits an audible pop
whenever playback is stopped or resumed, or during silent periods of an
audio stream. Initialise the IZD bit to the 0 to eliminate these pops.
The Infinite Zero Detection (IZD) feature on the DAC causes the output
to be shunted to Vcap after 2048 samples of silence. This discharges the
AC coupling capacitor through the output and causes the aforementioned
pop/click noise.
The behaviour of the IZD bit is described on page 15 of the WM8768GEDS
datasheet: "With IZD=1, applying MUTE for 1024 consecutive input samples
will cause all outputs to be connected directly to VCAP. This also
happens if 2048 consecutive zero input samples are applied to all 6
channels, and IZD=0. It will be removed as soon as any channel receives
a non-zero input". I believe the second sentence might be referring to
IZD=1 instead of IZD=0 given the observed behaviour of the card.
This change should make the DAC initialisation consistent with
Creative's Windows driver, as this popping persists when initialising
the card in Linux and soft rebooting into Windows, but is not present on
a cold boot to Windows.
Signed-off-by: Alex Stanoev <alex@astanoev.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7bb6ad5685f05685dd8a6a5eda7bfcd14d5f95b upstream.
The Lenovo G50-30, like other G50 models, has a Conexant codec that
requires a quirk for its inverted stereo dmic.
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1249364
Reported-by: Alexander Ploumistos <alex.ploumistos@gmail.com>
Tested-by: Alexander Ploumistos <alex.ploumistos@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeremy Cline <jcline@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 3c229b3f2dd8133f61bb81d3cb018be92f4bba39 upstream.
Fix a long-existing small nasty bug in the map_pages() implementation which
leads to overwriting already written pte entries with zero, *if* map_pages() is
called a second time with an end address which isn't aligned on a pmd boundry.
This happens for example if we want to remap only the text segment read/write
in order to run alternative patching on the code. Exiting the loop when we
reach the end address fixes this.
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 95691e3eddc41da2d1cd3cca51fecdfb46bd85bc upstream.
Currently, "disable_clkrun" yenta_socket module parameter is only
implemented for TI CardBus bridges.
Add also an implementation for Ricoh bridges that have the necessary
setting documented in publicly available datasheets.
Tested on a RL5C476II with a Sunrich C-160 CardBus NIC that doesn't work
correctly unless the CLKRUN protocol is disabled.
Let's also make it clear in its description that the "disable_clkrun"
module parameter only works on these two previously mentioned brands of
CardBus bridges.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Cc: stable@vger.kernel.org
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 92e2921f7eee63450a5f953f4b15dc6210219430 upstream.
When an invalid mount option is passed to jffs2, jffs2_parse_options()
will fail and jffs2_sb_info will be freed, but then jffs2_sb_info will
be used (use-after-free) and freeed (double-free) in jffs2_kill_sb().
Fix it by removing the buggy invocation of kfree() when getting invalid
mount options.
Fixes: 92abc475d8 ("jffs2: implement mount option parsing and compression overriding")
Cc: stable@kernel.org
Signed-off-by: Hou Tao <houtao1@huawei.com>
Reviewed-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit e7c6a55606b5c46b449d76588968b4d8caae903f upstream.
Devices with compatible="pmbus" field have zero initial page count,
and pmbus_clear_faults() being called before the page count auto-
detection does not actually clear faults because it depends on the
page count. Non-cleared faults in its turn may fail the subsequent
page count auto-detection.
This patch fixes this problem by calling pmbus_clear_fault_page()
for currently set page and calling pmbus_clear_faults() after the
page count was detected.
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Bazhenov <bazhenov.dn@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 2d6cb6edd2c7fb4f40998895bda45006281b1ac5 upstream.
refill->end record the last key of writeback, for example, at the first
time, keys (1,128K) to (1,1024K) are flush to the backend device, but
the end key (1,1024K) is not included, since the bellow code:
if (bkey_cmp(k, refill->end) >= 0) {
ret = MAP_DONE;
goto out;
}
And in the next time when we refill writeback keybuf again, we searched
key start from (1,1024K), and got a key bigger than it, so the key
(1,1024K) missed.
This patch modify the above code, and let the end key to be included to
the writeback key buffer.
Signed-off-by: Tang Junhui <tang.junhui.linux@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 53c13ba8ed39e89f21a0b98f4c8a241bb44e483d upstream.
Clang warns that the declaration of jiffies in include/linux/jiffies.h
doesn't match the definition in arch/x86/time/kernel.c:
arch/x86/kernel/time.c:29:42: warning: section does not match previous declaration [-Wsection]
__visible volatile unsigned long jiffies __cacheline_aligned = INITIAL_JIFFIES;
^
./include/linux/cache.h:49:4: note: expanded from macro '__cacheline_aligned'
__section__(".data..cacheline_aligned")))
^
./include/linux/jiffies.h:81:31: note: previous attribute is here
extern unsigned long volatile __cacheline_aligned_in_smp __jiffy_arch_data jiffies;
^
./arch/x86/include/asm/cache.h:20:2: note: expanded from macro '__cacheline_aligned_in_smp'
__page_aligned_data
^
./include/linux/linkage.h:39:29: note: expanded from macro '__page_aligned_data'
#define __page_aligned_data __section(.data..page_aligned) __aligned(PAGE_SIZE)
^
./include/linux/compiler_attributes.h:233:56: note: expanded from macro '__section'
#define __section(S) __attribute__((__section__(#S)))
^
1 warning generated.
The declaration was changed in commit 7c30f352c852 ("jiffies.h: declare
jiffies and jiffies_64 with ____cacheline_aligned_in_smp") but wasn't
updated here. Make them match so Clang no longer warns.
Fixes: 7c30f352c852 ("jiffies.h: declare jiffies and jiffies_64 with ____cacheline_aligned_in_smp")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181013005311.28617-1-natechancellor@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 94d7ee0baa8b764cf64ad91ed69464c1a6a0066b upstream.
The code following l2tp_tunnel_find() expects that a new reference is
held on sk. Either sk_receive_skb() or the discard_put error path will
drop a reference from the tunnel's socket.
This issue exists in both l2tp_ip and l2tp_ip6.
Fixes: a3c18422a4b4 ("l2tp: hold socket before dropping lock in l2tp_ip{, 6}_recv()")
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9bd616e3dbedfc103f158197c8ad93678849b1ed upstream.
The cpuidle_devices per-CPU variable is only defined when CPU_IDLE is
enabled. Commit c8cc7d4de7 ("sched/idle: Reorganize the idle loop")
removed the #ifdef CONFIG_CPU_IDLE around cpuidle_idle_call() with the
compiler optimising away __this_cpu_read(cpuidle_devices). However, with
CONFIG_UBSAN && !CONFIG_CPU_IDLE, this optimisation no longer happens
and the kernel fails to link since cpuidle_devices is not defined.
This patch introduces an accessor function for the current CPU cpuidle
device (returning NULL when !CONFIG_CPU_IDLE) and uses it in
cpuidle_idle_call().
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: 4.5+ <stable@vger.kernel.org> # 4.5+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b59167ac7bafd804c91e49ad53c6d33a7394d4c8 upstream.
Eric reported that a sequence count loop using this_cpu_read() got
optimized out. This is wrong, this_cpu_read() must imply READ_ONCE()
because the interface is IRQ-safe, therefore an interrupt can have
changed the per-cpu value.
Fixes: 7c3576d261 ("[PATCH] i386: Convert PDA into the percpu section")
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: hpa@zytor.com
Cc: eric.dumazet@gmail.com
Cc: bp@alien8.de
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20181011104019.748208519@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit baa9be4ffb55876923dc9716abc0a448e510ba30 upstream.
With a very low cpu.cfs_quota_us setting, such as the minimum of 1000,
distribute_cfs_runtime may not empty the throttled_list before it runs
out of runtime to distribute. In that case, due to the change from
c06f04c704 to put throttled entries at the head of the list, later entries
on the list will starve. Essentially, the same X processes will get pulled
off the list, given CPU time and then, when expired, get put back on the
head of the list where distribute_cfs_runtime will give runtime to the same
set of processes leaving the rest.
Fix the issue by setting a bit in struct cfs_bandwidth when
distribute_cfs_runtime is running, so that the code in throttle_cfs_rq can
decide to put the throttled entry on the tail or the head of the list. The
bit is set/cleared by the callers of distribute_cfs_runtime while they hold
cfs_bandwidth->lock.
This is easy to reproduce with a handful of CPU consumers. I use 'crash' on
the live system. In some cases you can simply look at the throttled list and
see the later entries are not changing:
crash> list cfs_rq.throttled_list -H 0xffff90b54f6ade40 -s cfs_rq.runtime_remaining | paste - - | awk '{print $1" "$4}' | pr -t -n3
1 ffff90b56cb2d200 -976050
2 ffff90b56cb2cc00 -484925
3 ffff90b56cb2bc00 -658814
4 ffff90b56cb2ba00 -275365
5 ffff90b166a45600 -135138
6 ffff90b56cb2da00 -282505
7 ffff90b56cb2e000 -148065
8 ffff90b56cb2fa00 -872591
9 ffff90b56cb2c000 -84687
10 ffff90b56cb2f000 -87237
11 ffff90b166a40a00 -164582
crash> list cfs_rq.throttled_list -H 0xffff90b54f6ade40 -s cfs_rq.runtime_remaining | paste - - | awk '{print $1" "$4}' | pr -t -n3
1 ffff90b56cb2d200 -994147
2 ffff90b56cb2cc00 -306051
3 ffff90b56cb2bc00 -961321
4 ffff90b56cb2ba00 -24490
5 ffff90b166a45600 -135138
6 ffff90b56cb2da00 -282505
7 ffff90b56cb2e000 -148065
8 ffff90b56cb2fa00 -872591
9 ffff90b56cb2c000 -84687
10 ffff90b56cb2f000 -87237
11 ffff90b166a40a00 -164582
Sometimes it is easier to see by finding a process getting starved and looking
at the sched_info:
crash> task ffff8eb765994500 sched_info
PID: 7800 TASK: ffff8eb765994500 CPU: 16 COMMAND: "cputest"
sched_info = {
pcount = 8,
run_delay = 697094208,
last_arrival = 240260125039,
last_queued = 240260327513
},
crash> task ffff8eb765994500 sched_info
PID: 7800 TASK: ffff8eb765994500 CPU: 16 COMMAND: "cputest"
sched_info = {
pcount = 8,
run_delay = 697094208,
last_arrival = 240260125039,
last_queued = 240260327513
},
Signed-off-by: Phil Auld <pauld@redhat.com>
Reviewed-by: Ben Segall <bsegall@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Fixes: c06f04c704 ("sched: Fix potential near-infinite distribute_cfs_runtime() loop")
Link: http://lkml.kernel.org/r/20181008143639.GA4019@pauld.bos.csb
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 13c1c5e4d7f887cba36c5e3df3faa22071c1469f upstream.
Add ELAN061C to the ACPI table to support Elan touchpad found in Lenovo
IdeaPad 330-15IGM.
Signed-off-by: Mikhail Nikiforov <jackxviichaos@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 665c365a77fbfeabe52694aedf3446d5f2f1ce42 upstream.
Commit 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more") checks the
transfer flags for URBs submitted from userspace via usbfs. However,
the check for whether the USBDEVFS_URB_SHORT_NOT_OK flag should be
allowed for a control transfer was added in the wrong place, before
the code has properly determined the direction of the control
transfer. (Control transfers are special because for them, the
direction is set by the bRequestType byte of the Setup packet rather
than direction bit of the endpoint address.)
This patch moves code which sets up the allow_short flag for control
transfers down after is_in has been set to the correct value.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+24a30223a4b609bb802e@syzkaller.appspotmail.com
Fixes: 7a68d9fb8510 ("USB: usbdevfs: sanitize flags more")
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 9ae24af3669111d418242caec8dd4ebd9ba26860 upstream.
num can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/usb/gadget/function/f_mass_storage.c:3177 fsg_lun_make() warn:
potential spectre issue 'fsg_opts->common->luns' [r] (local cap)
Fix this by sanitizing num before using it to index
fsg_opts->common->luns
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Felipe Balbi <felipe.balbi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f976d0e5747ca65ccd0fb2a4118b193d70aa1836 upstream.
The usb standard ("Universal Serial Bus Class Definitions for Communication
Devices") distiguishes between "consistent signals" (DSR, DCD), and
"irregular signals" (break, ring, parity error, framing error, overrun).
The bits of "irregular signals" are set, if this error/event occurred on
the device side and are immeadeatly unset, if the serial state notification
was sent.
Like other drivers of real serial ports do, just the occurence of those
events should be counted in serial_icounter_struct (but no 1->0
transitions).
Signed-off-by: Tobias Herzog <t-herzog@gmx.de>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0295e39595e1146522f2722715dba7f7fba42217 upstream.
hdr.cmd can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/infiniband/core/ucm.c:1127 ib_ucm_write() warn: potential
spectre issue 'ucm_cmd_table' [r] (local cap)
Fix this by sanitizing hdr.cmd before using it to index
ucm_cmd_table.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit a3671a4f973ee9d9621d60166cc3b037c397d604 upstream.
hdr.cmd can be indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/infiniband/core/ucma.c:1686 ucma_write() warn: potential
spectre issue 'ucma_cmd_table' [r] (local cap)
Fix this by sanitizing hdr.cmd before using it to index
ucm_cmd_table.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit efa61c8cf2950ab5c0e66cff3cabe2a2b24e81ba upstream.
pin_index can be indirectly controlled by user-space, hence leading
to a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/ptp/ptp_chardev.c:253 ptp_ioctl() warn: potential spectre issue
'ops->pin_config' [r] (local cap)
Fix this by sanitizing pin_index before using it to index
ops->pin_config, and before passing it as an argument to
function ptp_set_pinfunc(), in which it is used to index
info->pin_config.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 169b803397499be85bdd1e3d07d6f5e3d4bd669e upstream.
the victim might've been rmdir'ed just before the lock_rename();
unlike the normal callers, we do not look the source up after the
parents are locked - we know it beforehand and just recheck that it's
still the child of what used to be its parent. Unfortunately,
the check is too weak - we don't spot a dead directory since its
->d_parent is unchanged, dentry is positive, etc. So we sail all
the way to ->rename(), with hosting filesystems _not_ expecting
to be asked renaming an rmdir'ed subdirectory.
The fix is easy, fortunately - the lock on parent is sufficient for
making IS_DEADDIR() on child safe.
Cc: stable@vger.kernel.org
Fixes: 9ae326a690 (CacheFiles: A cache that backs onto a mounted filesystem)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit d312fefea8387503375f728855c9a62de20c9665 ]
ahci_pci_reset_controller() calls ahci_reset_controller(), which may
fail, but ignores the result code and always returns success. This
may result in failures like below
ahci 0000:02:00.0: version 3.0
ahci 0000:02:00.0: enabling device (0000 -> 0003)
ahci 0000:02:00.0: SSS flag set, parallel bus scan disabled
ahci 0000:02:00.0: controller reset failed (0xffffffff)
ahci 0000:02:00.0: failed to stop engine (-5)
... repeated many times ...
ahci 0000:02:00.0: failed to stop engine (-5)
Unable to handle kernel paging request at virtual address ffff0000093f9018
...
PC is at ahci_stop_engine+0x5c/0xd8 [libahci]
LR is at ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
...
[<ffff000000a17014>] ahci_stop_engine+0x5c/0xd8 [libahci]
[<ffff000000a196b4>] ahci_deinit_port.constprop.12+0x1c/0xc0 [libahci]
[<ffff000000a197d8>] ahci_init_controller+0x80/0x168 [libahci]
[<ffff000000a260f8>] ahci_pci_init_controller+0x60/0x68 [ahci]
[<ffff000000a26f94>] ahci_init_one+0x75c/0xd88 [ahci]
[<ffff000008430324>] local_pci_probe+0x3c/0xb8
[<ffff000008431728>] pci_device_probe+0x138/0x170
[<ffff000008585e54>] driver_probe_device+0x2dc/0x458
[<ffff0000085860e4>] __driver_attach+0x114/0x118
[<ffff000008583ca8>] bus_for_each_dev+0x60/0xa0
[<ffff000008585638>] driver_attach+0x20/0x28
[<ffff0000085850b0>] bus_add_driver+0x1f0/0x2a8
[<ffff000008586ae0>] driver_register+0x60/0xf8
[<ffff00000842f9b4>] __pci_register_driver+0x3c/0x48
[<ffff000000a3001c>] ahci_pci_driver_init+0x1c/0x1000 [ahci]
[<ffff000008083918>] do_one_initcall+0x38/0x120
where an obvious hardware level failure results in an unnecessary 15 second
delay and a subsequent crash.
So record the result code of ahci_reset_controller() and relay it, rather
than ignoring it.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9039f3ef446e9ffa200200c934f049add9e58426 ]
The SCTP program may sleep under a spinlock, and the function call path is:
sctp_generate_t3_rtx_event (acquire the spinlock)
sctp_do_sm
sctp_side_effects
sctp_cmd_interpreter
sctp_make_init_ack
sctp_pack_cookie
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
For the same reason, the orinoco driver may sleep in interrupt handler,
and the function call path is:
orinoco_rx_isr_tasklet
orinoco_rx
orinoco_mic
crypto_shash_setkey
shash_setkey_unaligned
kmalloc(GFP_KERNEL)
To fix it, GFP_KERNEL is replaced with GFP_ATOMIC.
This bug is found by my static analysis tool and my code review.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit eb66ae030829605d61fbef1909ce310e29f78821 upstream.
This is a backport to stable 4.4.y.
Jann Horn points out that our TLB flushing was subtly wrong for the
mremap() case. What makes mremap() special is that we don't follow the
usual "add page to list of pages to be freed, then flush tlb, and then
free pages". No, mremap() obviously just _moves_ the page from one page
table location to another.
That matters, because mremap() thus doesn't directly control the
lifetime of the moved page with a freelist: instead, the lifetime of the
page is controlled by the page table locking, that serializes access to
the entry.
As a result, we need to flush the TLB not just before releasing the lock
for the source location (to avoid any concurrent accesses to the entry),
but also before we release the destination page table lock (to avoid the
TLB being flushed after somebody else has already done something to that
page).
This also makes the whole "need_flush" logic unnecessary, since we now
always end up flushing the TLB for every valid entry.
Reported-and-tested-by: Jann Horn <jannh@google.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[will: backport to 4.4 stable]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ff002269a4ee9c769dbf9365acef633ebcbd6cbe ]
The idx in vhost_vring_ioctl() was controlled by userspace, hence a
potential exploitation of the Spectre variant 1 vulnerability.
Fixing this by sanitizing idx before using it to index d->vqs.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7de414a9dd91426318df7b63da024b2b07e53df5 ]
Most callers of pskb_trim_rcsum() simply drop the skb when
it fails, however, ip_check_defrag() still continues to pass
the skb up to stack. This is suspicious.
In ip_check_defrag(), after we learn the skb is an IP fragment,
passing the skb to callers makes no sense, because callers expect
fragments are defrag'ed on success. So, dropping the skb when we
can't defrag it is reasonable.
Note, prior to commit 88078d98d1bb, this is not a big problem as
checksum will be fixed up anyway. After it, the checksum is not
correct on failure.
Found this during code review.
Fixes: 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends")
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b336decab22158937975293aea79396525f92bb3 ]
syzbot reported an use-after-free involving sctp_id2asoc. Dmitry Vyukov
helped to root cause it and it is because of reading the asoc after it
was freed:
CPU 1 CPU 2
(working on socket 1) (working on socket 2)
sctp_association_destroy
sctp_id2asoc
spin lock
grab the asoc from idr
spin unlock
spin lock
remove asoc from idr
spin unlock
free(asoc)
if asoc->base.sk != sk ... [*]
This can only be hit if trying to fetch asocs from different sockets. As
we have a single IDR for all asocs, in all SCTP sockets, their id is
unique on the system. An application can try to send stuff on an id
that matches on another socket, and the if in [*] will protect from such
usage. But it didn't consider that as that asoc may belong to another
socket, it may be freed in parallel (read: under another socket lock).
We fix it by moving the checks in [*] into the protected region. This
fixes it because the asoc cannot be freed while the lock is held.
Reported-by: syzbot+c7dd55d7aec49d48e49a@syzkaller.appspotmail.com
Acked-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 6b839b6cf9eada30b086effb51e5d6076bafc761 ]
rtl_rx() and rtl_tx() are called only if the respective bits are set
in the interrupt status register. Under high load NAPI may not be
able to process all data (work_done == budget) and it will schedule
subsequent calls to the poll callback.
rtl_ack_events() however resets the bits in the interrupt status
register, therefore subsequent calls to rtl8169_poll() won't call
rtl_rx() and rtl_tx() - chip interrupts are still disabled.
Fix this by calling rtl_rx() and rtl_tx() independent of the bits
set in the interrupt status register. Both functions will detect
if there's nothing to do for them.
Fixes: da78dbff2e ("r8169: remove work from irq handler.")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 30549aab146ccb1275230c3b4b4bc6b4181fd54e ]
When building stmmac, it is only possible to select CONFIG_DWMAC_GENERIC,
or any of the glue drivers, when CONFIG_STMMAC_PLATFORM is set.
The only exception is CONFIG_STMMAC_PCI.
When calling of_mdiobus_register(), it will call our ->reset()
callback, which is set to stmmac_mdio_reset().
Most of the code in stmmac_mdio_reset() is protected by a
"#if defined(CONFIG_STMMAC_PLATFORM)", which will evaluate
to false when CONFIG_STMMAC_PLATFORM=m.
Because of this, the phy reset gpio will only be pulled when
stmmac is built as built-in, but not when built as modules.
Fix this by using "#if IS_ENABLED()" instead of "#if defined()".
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit b6168562c8ce2bd5a30e213021650422e08764dc ]
In ethtool_ioctl(), the ioctl command 'ethcmd' is checked through a switch
statement to see whether it is necessary to pre-process the ethtool
structure, because, as mentioned in the comment, the structure
ethtool_rxnfc is defined with padding. If yes, a user-space buffer 'rxnfc'
is allocated through compat_alloc_user_space(). One thing to note here is
that, if 'ethcmd' is ETHTOOL_GRXCLSRLALL, the size of the buffer 'rxnfc' is
partially determined by 'rule_cnt', which is actually acquired from the
user-space buffer 'compat_rxnfc', i.e., 'compat_rxnfc->rule_cnt', through
get_user(). After 'rxnfc' is allocated, the data in the original user-space
buffer 'compat_rxnfc' is then copied to 'rxnfc' through copy_in_user(),
including the 'rule_cnt' field. However, after this copy, no check is
re-enforced on 'rxnfc->rule_cnt'. So it is possible that a malicious user
race to change the value in the 'compat_rxnfc->rule_cnt' between these two
copies. Through this way, the attacker can bypass the previous check on
'rule_cnt' and inject malicious data. This can cause undefined behavior of
the kernel and introduce potential security risk.
This patch avoids the above issue via copying the value acquired by
get_user() to 'rxnfc->rule_cn', if 'ethcmd' is ETHTOOL_GRXCLSRLALL.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 38b4f18d56372e1e21771ab7b0357b853330186c ]
gred_change_table_def() takes a pointer to TCA_GRED_DPS attribute,
and expects it will be able to interpret its contents as
struct tc_gred_sopt. Pass the correct gred attribute, instead of
TCA_OPTIONS.
This bug meant the table definition could never be changed after
Qdisc was initialized (unless whatever TCA_OPTIONS contained both
passed netlink validation and was a valid struct tc_gred_sopt...).
Old behaviour:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
RTNETLINK answers: Invalid argument
Now:
$ ip link add type dummy
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
$ tc qdisc replace dev dummy0 parent root handle 7: \
gred setup vqs 4 default 0
Fixes: f62d6b936d ("[PKT_SCHED]: GRED: Use central VQ change procedure")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4ba4c566ba8448a05e6257e0b98a21f1a0d55315 ]
The loop wants to skip previously dumped addresses, so loops until
current index >= saved index. If the message fills it wants to save
the index for the next address to dump - ie., the one that did not
fit in the current message.
Currently, it is incrementing the index counter before comparing to the
saved index, and then the saved index is off by 1 - it assumes the
current address is going to fit in the message.
Change the index handling to increment only after a succesful dump.
Fixes: 502a2ffd73 ("ipv6: convert idev_list to list macros")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit ee1abcf689353f36d9322231b4320926096bdee0 ]
Commit a61bbcf28a ("[NET]: Store skb->timestamp as offset to a base
timestamp") introduces a neighbour control buffer and zeroes it out in
ndisc_rcv(), as ndisc_recv_ns() uses it.
Commit f2776ff047 ("[IPV6]: Fix address/interface handling in UDP and
DCCP, according to the scoping architecture.") introduces the usage of the
IPv6 control buffer in protocol error handlers (e.g. inet6_iif() in
present-day __udp6_lib_err()).
Now, with commit b94f1c0904 ("ipv6: Use icmpv6_notify() to propagate
redirect, instead of rt6_redirect()."), we call protocol error handlers
from ndisc_redirect_rcv(), after the control buffer is already stolen and
some parts are already zeroed out. This implies that inet6_iif() on this
path will always return zero.
This gives unexpected results on UDP socket lookup in __udp6_lib_err(), as
we might actually need to match sockets for a given interface.
Instead of always claiming the control buffer in ndisc_rcv(), do that only
when needed.
Fixes: b94f1c0904 ("ipv6: Use icmpv6_notify() to propagate redirect, instead of rt6_redirect().")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0fe5119e267f3e3d8ac206895f5922195ec55a8a upstream.
Recently a check was added which prevents marking of routers with zero
source address, but for IPv6 that cannot happen as the relevant RFCs
actually forbid such packets:
RFC 2710 (MLDv1):
"To be valid, the Query message MUST
come from a link-local IPv6 Source Address, be at least 24 octets
long, and have a correct MLD checksum."
Same goes for RFC 3810.
And also it can be seen as a requirement in ipv6_mc_check_mld_query()
which is used by the bridge to validate the message before processing
it. Thus any queries with :: source address won't be processed anyway.
So just remove the check for zero IPv6 source address from the query
processing function.
Fixes: 5a2de63fd1a5 ("bridge: do not add port to router list when receives query with source 0.0.0.0")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cc: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 5a2de63fd1a59c30c02526d427bc014b98adf508 upstream.
Based on RFC 4541, 2.1.1. IGMP Forwarding Rules
The switch supporting IGMP snooping must maintain a list of
multicast routers and the ports on which they are attached. This
list can be constructed in any combination of the following ways:
a) This list should be built by the snooping switch sending
Multicast Router Solicitation messages as described in IGMP
Multicast Router Discovery [MRDISC]. It may also snoop
Multicast Router Advertisement messages sent by and to other
nodes.
b) The arrival port for IGMP Queries (sent by multicast routers)
where the source address is not 0.0.0.0.
We should not add the port to router list when receives query with source
0.0.0.0.
Reported-by: Ying Xu <yinxu@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit da15fc2fa9c07b23db8f5e479bd8a9f0d741ca07 ]
The Yocto build system does a 'make clean' when rebuilding due to
changed dependencies, and that consistently fails for me (causing the
whole BSP build to fail) with errors such as
| find: '[...]/perf/1.0-r9/perf-1.0/plugin_mac80211.so': No such file or directory
| find: '[...]/perf/1.0-r9/perf-1.0/plugin_mac80211.so': No such file or directory
| find: find: '[...]/perf/1.0-r9/perf-1.0/libtraceevent.a''[...]/perf/1.0-r9/perf-1.0/libtraceevent.a': No such file or directory: No such file or directory
|
[...]
| find: cannot delete '/mnt/xfs/devel/pil/yocto/tmp-glibc/work/wandboard-oe-linux-gnueabi/perf/1.0-r9/perf-1.0/util/.pstack.o.cmd': No such file or directory
Apparently (despite the comment), 'make clean' ends up launching
multiple sub-makes that all want to remove the same things - perhaps
this only happens in combination with a O=... parameter. In any case, we
don't lose much by explicitly disabling the parallelism for the clean
target, and it makes automated builds much more reliable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180705131527.19749-1-linux@rasmusvillemoes.dk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit d616f81cdd2a21edfa90a595a4e9b143f5ba8414 ]
Added support for is25wp032, is25wp064 and is25wp128.
Signed-off-by: Kimmo Rautkoski <ext-kimmo.rautkoski@vaisala.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
[ Adrian Bunk: Trivial adaption to changed context. ]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit ac081c3be3fae6d0cc3e1862507fca3862d30b67 ]
On non-preempt kernels this loop can take a long time (more than 50 ticks)
processing through entries.
Link: http://lkml.kernel.org/r/20181010172623.57033-1-khazhy@google.com
Signed-off-by: Khazhismel Kumykov <khazhy@google.com>
Acked-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eea96566c189c77e5272585984eb2729881a2f1d ]
The maximum CPU frequency for the i.MX53 QSB is 1GHz, so disable the
1.2GHz OPP. This makes the board work again with configs that have
cpufreq enabled like imx_v6_v7_defconfig on which the board stopped
working with the addition of cpufreq-dt support.
Fixes: 791f416608 ("ARM: dts: imx53: add cpufreq-dt support")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 68fe55680d0f3342969f49412fceabb90bdfadba ]
Fix a commit 3021773c7c3e ("MIPS: DEC: Avoid la pseudo-instruction in
delay slots") regression and remove assembly errors:
arch/mips/dec/int-handler.S: Assembler messages:
arch/mips/dec/int-handler.S:162: Error: Macro used $at after ".set noat"
arch/mips/dec/int-handler.S:163: Error: Macro used $at after ".set noat"
arch/mips/dec/int-handler.S:229: Error: Macro used $at after ".set noat"
arch/mips/dec/int-handler.S:230: Error: Macro used $at after ".set noat"
triggering with with the CPU_DADDI_WORKAROUNDS option set and the DADDIU
instruction. This is because with that option in place the instruction
becomes a macro, which expands to an LI/DADDU (or actually ADDIU/DADDU)
sequence that uses $at as a temporary register.
With CPU_DADDI_WORKAROUNDS we only support `-msym32' compilation though,
and this is already enforced in arch/mips/Makefile, so choose the 32-bit
expansion variant for the supported configurations and then replace the
64-bit variant with #error just in case.
Fixes: 3021773c7c3e ("MIPS: DEC: Avoid la pseudo-instruction in delay slots")
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 4.8+
Patchwork: https://patchwork.linux-mips.org/patch/16893/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 2a83fba6cae89dd9c0625e68ff8ffff791c67ac0 ]
This patch reverts two previous applied patches to fix an issue
that appeared when using SGMII based SFP modules. In the current
state the driver will try to reset the PHY before obtaining the
phy_addr of the SGMII attached PHY. That leads to an error in
e1000_write_phy_reg_sgmii_82575. Causing the initialization to
fail:
igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
igb: Copyright (c) 2007-2014 Intel Corporation.
igb: probe of ????:??:??.? failed with error -3
The patches being reverted are:
commit 182785335447957409282ca745aa5bc3968facee
Author: Aaron Sierra <asierra@xes-inc.com>
Date: Tue Nov 29 10:03:56 2016 -0600
igb: reset the PHY before reading the PHY ID
commit 440aeca4b9858248d8f16d724d9fa87a4f65fa33
Author: Matwey V Kornilov <matwey@sai.msu.ru>
Date: Thu Nov 24 13:32:48 2016 +0300
igb: Explicitly select page 0 at initialization
The first reverted patch directly causes the problem mentioned above.
In case of SGMII the phy_addr is not known at this point and will
only be obtained by 'igb_get_phy_id_82575' further down in the code.
The second removed patch selects forces selection of page 0 in the
PHY. Something that the reset tries to address as well.
As pointed out by Alexander Duzck, the patch below fixes the same
issue but in the proper location:
commit 4e684f59d760a2c7c716bb60190783546e2d08a1
Author: Chris J Arges <christopherarges@gmail.com>
Date: Wed Nov 2 09:13:42 2016 -0500
igb: Workaround for igb i210 firmware issue
Reverts: 440aeca4b9858248d8f16d724d9fa87a4f65fa33.
Reverts: 182785335447957409282ca745aa5bc3968facee.
Signed-off-by: Christian Grönke <c.groenke@infodas.de>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cea8cd498f4f1c30ea27e3664b3c671e495c4fce ]
When the immediate encoded in the instruction is accessed, it is sign
extended due to being a signed value being assigned to a signed integer.
The ISA specifies that this operation is an unsigned operation.
The sign extension leads us to incorrectly decode:
801e9c8e: cbf1 sw ra,68(sp)
As having an immediate of 1073741809.
Since the instruction format does not specify signed/unsigned, and this
is currently the only location to use this instuction format, change it
to an unsigned immediate.
Fixes: bb9bc4689b9c ("MIPS: Calculate microMIPS ra properly when unwinding the stack")
Suggested-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Cc: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: Miodrag Dinic <miodrag.dinic@imgtec.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/16957/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 934767c56b0d9dbb95a40e9e6e4d9dcdc3a165ad ]
The return status of the adapter check on KERNEL_PANIC is supposed to be
the upper 16 bits of the OMR status register.
Fixes: c421530bf848604e (scsi: aacraid: Reorder Adpater status check)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 19cdead3e2ef8ed765c5d1ce48057ca9d97b5094 ]
On slave list updates, the bonding driver computes its hard_header_len
as the maximum of all enslaved devices's hard_header_len.
If the slave list is empty, e.g. on last enslaved device removal,
ETH_HLEN is used.
Since the bonding header_ops are set only when the first enslaved
device is attached, the above can lead to header_ops->create()
being called with the wrong skb headroom in place.
If bond0 is configured on top of ipoib devices, with the
following commands:
ifup bond0
for slave in $BOND_SLAVES_LIST; do
ip link set dev $slave nomaster
done
ping -c 1 <ip on bond0 subnet>
we will obtain a skb_under_panic() with a similar call trace:
skb_push+0x3d/0x40
push_pseudo_header+0x17/0x30 [ib_ipoib]
ipoib_hard_header+0x4e/0x80 [ib_ipoib]
arp_create+0x12f/0x220
arp_send_dst.part.19+0x28/0x50
arp_solicit+0x115/0x290
neigh_probe+0x4d/0x70
__neigh_event_send+0xa7/0x230
neigh_resolve_output+0x12e/0x1c0
ip_finish_output2+0x14b/0x390
ip_finish_output+0x136/0x1e0
ip_output+0x76/0xe0
ip_local_out+0x35/0x40
ip_send_skb+0x19/0x40
ip_push_pending_frames+0x33/0x40
raw_sendmsg+0x7d3/0xb50
inet_sendmsg+0x31/0xb0
sock_sendmsg+0x38/0x50
SYSC_sendto+0x102/0x190
SyS_sendto+0xe/0x10
do_syscall_64+0x67/0x180
entry_SYSCALL64_slow_path+0x25/0x25
This change addresses the issue avoiding updating the bonding device
hard_header_len when the slaves list become empty, forbidding to
shrink it below the value used by header_ops->create().
The bug is there since commit 54ef313714 ("[PATCH] bonding: Handle large
hard_header_len") but the panic can be triggered only since
commit fc791b633515 ("IB/ipoib: move back IB LL address into the hard
header").
Reported-by: Norbert P <noe@physik.uzh.ch>
Fixes: 54ef313714 ("[PATCH] bonding: Handle large hard_header_len")
Fixes: fc791b633515 ("IB/ipoib: move back IB LL address into the hard header")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 9e578b37505018622dfafc40eed7cd78ff2af221 ]
platform_get_irq() returns an error code, but the tegra-devfreq
driver ignores it and always returns -ENODEV. This is not correct,
and prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print and propagate the return value of platform_get_irq on failure.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 27d30400c448264c1ac9434cb836de0c230af213 ]
platform_get_irq() returns an error code, but the spdif_in driver
ignores it and always returns -EINVAL. This is not correct, and
prevents -EPROBE_DEFER from being propagated properly.
Notice that platform_get_irq() no longer returns 0 on error:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=e330b9a6bb35dc7097a4f02cb1ae7b6f96df92af
Print error message and propagate the return value of platform_get_irq
on failure.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
