During recovery, if another PD down notification received because
of crash then handle the case. If debug enabled then BUG_ON to
debug the second crash.
CRs-fixed: 1067873
Change-Id: I6e8e92ca0ee11830f933e198fea502c915d36e59
Signed-off-by: Prashanth Bhatta <bhattap@codeaurora.org>
During recovery, if not able to force enable hardware clocks then
do top level reset only.
CRs-fixed: 1067868
Change-Id: Ie23ca022c94cd214a9e415e9fb774055cfaf881d
Signed-off-by: Prashanth Bhatta <bhattap@codeaurora.org>
During an timeout event in the SDE rotator driver, a spinlock with IRQ
is disabled in order to capture the rotator hw status registers. If
during this time performs an evtlog timeout logging, a mutex_lock
within the logging sequence will cause a panic. We must and only should
perform the evtlog timeout logging after the spinlock is released.
CRs-Fixed: 1067811
Change-Id: I56b7e5713069ad8ac8d5ae43a492a0ab0f4e82ff
Signed-off-by: Benjamin Chan <bkchan@codeaurora.org>
On msmcobalt reference platform, earpiece path is not connected
to receiver, instead speaker path is used as receiver. So handset
AANC(Adaptive Active Noise cancellation) needs to be supported
on speaker path. Change enables ANC support on speaker path.
Change-Id: I8104994adc30810085cce73662f5abd5e15106ad
Signed-off-by: Sudheer Papothi <spapothi@codeaurora.org>
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
In msmcobalt platform, speaker path is used for handset mode also.
Add the mixer control to change gain in handset mode.
Change-Id: Ia291f7449cd04a855102a03324f7cdcb6f13dad0
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
Dynamic detection between wcd9335 and wcd934x codecs is supported on
msmcobalt. Probe sequence of the two codec drivers can occur in any
order. MCLK initialization is common for the two codecs which gets
called twice. Avoid wcd934x codec's probe sequence from resetting
wcd9335 codec's native mclk pinctrl if the pinctrl is already
initialized.
CRs-Fixed: 1066167
Change-Id: Idf65e15e08bb856d65b992b996cffa6ef2e6f974
Signed-off-by: Meng Wang <mwang@codeaurora.org>
According to vendor's suggestion, reset pin and interrupt pin must be
pulled down before touchpanel controller power up. This is required
for all Goodix devices.
Change-Id: If16fab02967abbd0c2a6e4365fed76f9e8729bc2
Signed-off-by: Bingzhe Cai <bingzhec@codeaurora.org>
Use macros instead of magic numbers for maximum i2c retries in
Goodix driver.
Change-Id: I9f7da9f43418cd1d423aaf331f41d37d13f248d4
Signed-off-by: Shantanu Jain <shjain@codeaurora.org>
Update the DMIC CLK and DATA registers to use the correct
settings required for DMIC High-Z on wcd934x. Registers
should be set to 0x6 for Slimbus mode and 0xD for I2C mode.
CRs-Fixed: 1059712
Change-Id: Ibe8ca2e40ee56708e8c84c174d12ce5841e6b1ce
Signed-off-by: Meng Wang <mwang@codeaurora.org>
This reverts commit <fae741edccb> ("usb: gsi: Queue control
notification on gsi_resume") as expected notification is not
queued resulting into mismatch of QMI transaction packet.
CRs-Fixed: 1067006
Change-Id: I4abdd79699d47054e268978aae9199f1d5d1ddcb
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
TMC abort needs to save TMC registers so that TMC data can be extracted
from device crash dumps.
Change-Id: I4339e84dc62e589e0f4d341e8143b1cd94a9cbe2
Signed-off-by: Shashank Mittal <mittals@codeaurora.org>
On client pushing message, allocate memory for event
data and copy before pushing to clients. This is to
avoid crash if client goes away before freeing the
memory.
Change-Id: Icff40d68d9b60617e8e3eb006eb697194b4e61f6
CRs-Fixed: 1065499
Signed-off-by: Sunil Paidimarri <hisunil@codeaurora.org>
IIR and ANC registers are not cacheable so add them to
volatile register list.
Change-Id: I99e45021ca90138b73aebe1f13a6af0f42c58227
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
WCD934X codec supports adaptive ANC(Active noise cancellation)
on ear and speaker path. Add the required changes to support
this feature.
Change-Id: I2a069fc208b080c1251f7aa473ae75ad02e883c8
Signed-off-by: Vidyakumar Athota <vathota@codeaurora.org>
Headphones support classH and classAB. Add support for
hifi, lowhifi, low power and ultra low power modes for classH.
Support hifi and lowhifi power modes for classAB.
CRs-Fixed: 1066331
Change-Id: I846f9704a5bf800583682f8dc2ec385a0ec64c61
Signed-off-by: Yeleswarapu Nagaradhesh <nagaradh@codeaurora.org>
TASHA_IS_1_1 macro checks only for version number.
This macro returns true for tavil codec. So modify
tasha macros to check for codec and version.
CRs-Fixed: 1066331
Change-Id: I5240e0ee888187a8185974ea288ce2cad62bd776
Signed-off-by: Yeleswarapu Nagaradhesh <nagaradh@codeaurora.org>
commit <5b42bd749e8c> ("usb: gadget: gsi: Optimize TRB's buffer
allocation functionality") is kicking ipa_work_handler state
machine as part of set_alt() for RNDIS function which results
into giving max_xfer_size_bytes_to_host value as zero as
RNDIS_INIT_MSG from host may not have received here. This results
into low throughput due to device is sending more than accepted
aggregated bytes as part of one USB transfer to host. Fix this
issue by delaying RNDIS IPA initialization till MESSAGE_PACKET_FILTER
is received from host which makes sure that proper aggregation
parameters are passed to IPA driver to configure hardware
accerlerated path.
For non-rndis tethered interface, ipa_usb_notify_cb() posts EVT_CONNECTED
to enable IPA GSI data path (i.e. calling ipa_data_path_enable() API).
CRs-Fixed: 1065003
Change-Id: I4ce62745c82b4488cb1370248ab64951497493cd
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
