On each sg of secure CMA buffer to set/clear page private bit,
we should use the sg_page(sg) rather than sg_page(sgt->sgl).
Change-Id: I05300d9d3a0931d2a0c113f945b45136e0dea01e
Signed-off-by: Hareesh Gundu <hareeshg@codeaurora.org>
Core IPA driver passes wrong end-point index to HAL
when generating aggregation force close parameters
values. Fixed the call to pass the correct index.
CRs-Fixed: 2082839
Change-Id: Icc0fd2ce8a23bf0e3334f54b27b850ebf92b58a1
Signed-off-by: Ghanim Fodi <gfodi@codeaurora.org>
After finishing initialization during PCIe probe, there is no need to
keep PCIe link up. Hence suspend PCIe link and power off device after
PCIe probe for QCA6290 chipset.
Change-Id: I1b07d7c9ef4c3a15ba1eb409a4c64f905e83dae4
Signed-off-by: Yue Ma <yuem@codeaurora.org>
The vibrator HAL expects vibration to be disabled when the 'enable'
time specified is 0. Fix this.
CRs-Fixed: 2083994
Change-Id: I12843233da5429ed2fd53f33617952b1dd0ddcd5
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Currently, when scrambler is disabled the TMDS clock ratio bit
is left untouched. Ideally the sink should reset this bit during
hot plug OR no-signal cases. However, the HDMI spec requires this
bit to be explicitly reset by the source.
Add support to reset this bit during scrambler disable.
Change-Id: I092f6cae84653940e2bdb9100df5e384084cf938
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
As per SMC Calling Convention, X4/W4, X5/W5 & X6/W6 registers
return state is unpredictable. But, inline assembly in scm
driver did not correctly specify output markers, which is
causing compiler to move instructions around when clang is
used to compile, which inturn causing deadlock and boot issue
during firmware loading. Add X4/W4, X5/W5 & X6/W6 registers
to output operand list to fix the deadlock during firmware
loading.
Change-Id: I1e4d51a58cd34c31fc63bcd21a20bfd15498bdc3
Signed-off-by: Satya Durga Srinivasu Prabhala <satyap@codeaurora.org>
PD down notifications reaches APPS only after WLAN HW is
reset. Because of this, there is a small window of time
in which APPS may try to access WLAN HW Copy Engine
registers and get into exception. To avoid this, FW has
implemented 2 stage reset sequence in which first HW is
halted rather than reset and then when FW PD is started
again, reset sequence is executed. Because of the 2
stage reset sequence, WLAN shutdown call back also needs
to be delayed as there may be some buffers submitted to
hardware and if they are freed then again HW exception
may be seen. Delay the shutdown call back till FW ready
happens at this time HW should be reset and clean state.
CRs-fixed: 2056443
Change-Id: Ie587f98d574f7c0a49a8480449fed44c1f4ab816
Signed-off-by: Anurag Chouhan <achouhan@codeaurora.org>
Disable CONFIG_DEVPORT config for msm8998.
As selinux policy requires this node to be not
accessible to userspace.
Change-Id: I302d71a56764504ec246ddb6a98d8c07094846e4
Signed-off-by: Mohammed Khajapasha <mkhaja@codeaurora.org>
Set FDE encryption key size to 256bit for sdm630
target.
Change-Id: I4314c1408fb6cadcdb8d81a02a4dccb55f3f9065
Signed-off-by: Neeraj Soni <neersoni@codeaurora.org>
Fix the out of bound ITARGET register programming by calculating the
LED_IRESOLUTION current dynamically based on the flash current requested
by the client.
CRs-Fixed: 2066263
Change-Id: Ifba232ab4af5493feef53e331bccdc55c6109246
Signed-off-by: Kiran Gunda <kgunda@codeaurora.org>
Add several defines and structs to allow IPA kernel tests running.
Change-Id: I9c8f114b28aa617bdf1bfe56b44b73852a178ece
Acked-by: Dmitry Kogan <dmitryk@qti.qualcomm.com>
Signed-off-by: Amir Levy <alevy@codeaurora.org>
Configure the sleep state for the wlan bootstrap pin for
msm8996. This configuration helps in power saving during
device sleep state.
CRs-Fixed: 1040537
Change-Id: Ia35f8bba901826b55722cb140c953f32b18610de
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
The QCA wlan chipset uses tlmm, msm and pmic gpio for the WLAN_EN
signal pin. The tlmm or msm gpio uses pinctrl or gpio library for
configuring the sleep/active state runtime.
The pmic gpio runtime configuration is not feasible using gpio
library or pinctrl framework. Convert the pmic gpio to fixed
regulator to runtime control(enable/disable) via regulator framework.
CRs-Fixed: 1040537
Change-Id: I4963c2753b463d5852a847a20fe280107abca337
Signed-off-by: Sarada Prasanna Garnayak <sgarna@codeaurora.org>
