Add the power supplies to vote for max supported voltage on the
regulator for mdss dsi. Also add mdss dsi node for the msm8998
v2.1 interposer.
Change-Id: I84cae6e7816834dfce0839faa41903f2f871782d
Signed-off-by: Ashish Garg <ashigarg@codeaurora.org>
Enable config IP_NF_MATCH_RPFILTER.
This option allows you to match packets whose replies would go out via
the interface the packet came in
Change-Id: I2a23346e726a8df8487aeb664d6316b3cf2b9d77
Signed-off-by: Ashwanth Goli <ashwanth@codeaurora.org>
Triggering Crash Dumper might actually change the values of
few GPU registers including VBIF. Hence dump those registers
ahead and skip them from the list which goes to crash dumper.
Change-Id: I37a53983a65bd8abfefa780053819de71df7f24f
Signed-off-by: Rajesh Kemisetti <rajeshk@codeaurora.org>
By default A5xx GPUs use CP crash dumper to get GPU
snapshot in case of any fault.
At times it is required to disable crash dumper
in case of any abnormalities, add support to do so.
Change-Id: Iea6497778bcd711e769f0e509103bd3bd0fd8574
Signed-off-by: Rajesh Kemisetti <rajeshk@codeaurora.org>
Reduce halt ack timeout to 25 ms from 100 ms to reduce delay in
mss shutdown path.
Change-Id: I935e35d5d848e564aad5987b1652546046f0927d
Signed-off-by: Avaneesh Kumar Dwivedi <akdwived@codeaurora.org>
Add a new RCG clock ops specific for the DP pixel clock source.
Change-Id: I2ec5ddcfd47af8362f76d76d153e30d4e2f45370
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Enable the configuration which keeps the CPR sensors active
when LDO is in auto-bypass mode. The sensors only stay
bypassed when LDO is regulating.
CRs-Fixed: 1027469
Change-Id: I6b8c2a3fd8fe22a64b6d24c458a7c60641195e45
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Add a DT property to adjust the open-loop voltage for the LDO
corners, this will be useful for voltage adjustments after
LDO characterization.
While at it, update the LDO MIN_VOLTAGE value for 8953.
CRs-Fixed: 1010052
Change-Id: I7479ebbf0ac7253eb355246d36f15a91ce96cd9a
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Change the LDO_EN bit definition for GFX LDO on MSM8953 and
remove the LDO bypass fusing logic as it is not supported.
While at it, add the debugfs node to disable ldo_mode.
Disable LDO mode: echo 1 > /d/msm_gfx_ldo/ldo_mode_disable
Enable LDO mode: echo 0 > /d/msm_gfx_ldo/ldo_mode_disable
CRs-Fixed: 989270
Change-Id: Ibc7aa921380e89da4963571408b89bc417dec245
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Remove all reference to internal code name msmtitanium
and replace them with msm8953, as there is an official
announcement for msm8953 SoC.
Change-Id: If99bbf20756a524c5a3bd7ba49366c29e158289e
Signed-off-by: Tirupathi Reddy <tirupath@codeaurora.org>
Enable the PWMs mapped to the RGB module and specify
the lpg-lut-size.
While at it, enable the haptics and flash node.
Change-Id: I83cf7882d1abb96c343973894c2a7ab3f932dfb1
Signed-off-by: Anirudh Ghayal <aghayal@codeaurora.org>
Currently one gic interrupt is mapped to one mpm pin.
Support multiple mpm pins to get enabled with single irq
with client drivers using enable_irq_wake API.
Change-Id: Iea575079c24ed0986b74fb6e86c7b8100474f19e
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
